TrueBlue
-
Posts
42 -
Joined
-
Last visited
-
Days Won
6
Content Type
Profiles
Forums
Gallery
Blogs
Events
Page News
Downloads
Posts posted by TrueBlue
-
-
Anyone know where I can get bed cover to fit the Defender or one made to fit my unit 60"wide and 39" long. I have a back rack so I lose 2" Something like the Cover My Bed one made for the Rangers. Plastic or Black Powder Coated Aluminum.
Thx
-
HI
anyone on here got a good clean 2019 Defender Max HD10 XT stock gauge cluster with approx 3500 miles or 5500 Klm that they want to sell or was thinking bout upgrading to newer style but worried about cost this way you would be getting something for your old one. I busted mine and looking for one with similar miles. A new one has "0" miles and you can't put the mileage back on it according to the dealer ??
Thanks
TB
-
-
Think I might of found it based on these findings you guys posted. The rear roll cage bolts on that side were loose and I would if never found it until they fell out 😮 so tomorrow I'll will test and advise.
Thanks. TB
-
I have a 2019 HD10 Max Cab and when I hit a bump like a round rock protruding from the ground I get a clunk noise coming from the rear left driver side and seems like it's around the rear door and right under back window area on that side ??? Very annoying !
Thanks in advance TB
-
Guys
I replaced replaced my Drivers side power window twice under warranty and now again outside warranty. I’ve cleaned the contacts and it works for a couple of weeks the fails again usually in the upward motion. What other switches are you guys using as a substitute?? part# and manufacture if you have one.
2019 Can Am Defender HD10 Max CabThanks
Bill
-
Looking for a set of 14” x137 rims for HD10 Max Cab 5+2 offset so I can have two set of tires and rims to swap.
Thx
TB
-
Make sure to run max air as rated on tire. No issues with clutching or turning them over. I use low gear when in hard rough areas. I’m at 7,000 Klm and original belt.
cheers
-
2” is what I found to keep front and rear tracking in the same rut.
Cheers
-
-
Yes the noise is gone . 😁
-
Well it was the front Diff and they replaced it. Funny how one dealer said never heard of it before and another dealer said bring it in two hrs and you’ll have it back. I quess I have a new dealer going forward. 👍😀
TB
-
A year later and that noise in the front end is still there and i’ve had enough. Today I took the drive shaft protector off the front section from steady/carrier bearing to the front Diff. I found the noise finally it’s that stupid Diff assy.
Now it’s dealer time to see if they will replace or fix the issue ! Still under 2 yr warranty.
TB
-
-
Ya that’s probably it ?
TB
-
-
Those little fans are great as well for $11 each
TB
-
Also put on Race Driven pads and no more squeal ! Installed LED lights from Amazon .
TB
-
Replaced the pads which only had 800 klm and not worn at all. Put on the Race Driven and no squeal !
TB
- 1
-
I didn’t remove the front drive shaft yet, I guess it’s just to much work and i’ll Live with the rattle for now !
TB
-
-
I know everyone don’t have a air blaster but under due care and caution !! Starter fluid works great but just a small amount. 😜
TB
- 1
-
I have the Maxxis Liberty ML3 30” on stock rims with 2” spacers in rear, no lift and the ride quality and handling is perfect. Highly recommend it. I don’t know why they don’t offer this option from factory or a dealer upgrade. Maybe they don’t know ??
TB
-
Here’s a pic of mine now with the 30”x10-14 Liberty ML3’s with 2” spacers in back. What a difference this made to the ride quality, I highly recommend this upgrade! Also I bought 15’ of this rubber cargo matting on sale at Princess Auto for $60 and made a template out of paper for the front and back floors. Then I took out back seats tops and bottoms and ran one piece from floor up and over the battery box area to bottom of seat belt area using push grommets. Then a piece all way up behind inside the frame right to steel bar under window and used the top grommets to hold it in place. It was a task but working it up slowly it fitted good. I cleaned everything good then finished off with Black Gorilla tape to seal everything up. I can honestly say that it’s 50% quieter again than factory and the cost was no where as expensive as Fat Mat Dyna Mat ?? or those speciality products plus I got the floor and back firewall done. Next I just ordered from Amazon that 2”x 50’ exhaust wrap $30 c/w straps that I’m doing the exhaust to help with some of them heat issues like those rubber dump stops sticking to chassis and it also quiets down exhaust. Oh almost forgot I picked up two of these little dual head 12v fans from Princess Auto again for $11 ea and wired them to the fuse block with a inline 5 amp fuse up by the wiper motor. It’s not Air conditioning but it sure helps 👍
TB
AC options before Limited
in Defender Talk
Posted
Anyone running a portable AC unit on prior Limited Editions ??? I've seen Zero Breeze Mark 2 units and wonder if that will work. Also just a window unit with small Honda Generator sticking out back window ???
looking at any ideas you guys have.
thanks
TB